Z-Wave the public standard

Z/IP GW Wrong Tap0 IP


#1

I compiled the Z/IP GW. Good.
Now I ran (I have a custom shield):

zipgateway -s /dev/ttySC1


121129937 Waiting for bridge
121129957 Version: Z-Wave 6.01, type 7
121130027 ................. the  version 0 ...............121130067 NVM version is 2
121130087 L2 HW addr 00:1e:32:1c:e5:0e
121130087 
121130087 ZIP_Router_Reset: pan_lladdr: f6:d6:0f:ce:00:01  Home ID = 0xce0fd6f6 
121130087 Tunnel prefix ::
121130087 
121130087 Lan address fd00:aaaa::03
121130087 
121130087 Han address fd00:bbbb::01
121130087 
121130087 Gateway address fd00:aaaa::1234
121130087 
121130087 Unsolicited address fd00:aaaa::1234
121130087 
....

but I don’t see any tap0 correctly configured:

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500                                               
        inet 192.168.1.81  netmask 255.255.255.0  broadcast 192.168.1.255                                
        inet6 fe80::5b8f:af79:9277:a7b0  prefixlen 64  scopeid 0x20<link>                                
        ether b8:27:eb:f0:43:81  txqueuelen 1000  (Ethernet)                                             
        RX packets 67261  bytes 65604928 (62.5 MiB) 
        RX errors 0  dropped 20  overruns 0  frame 0                                                     
        TX packets 41463  bytes 5710271 (5.4 MiB)   
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0                                       

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536        
        inet 127.0.0.1  netmask 255.0.0.0           
        inet6 ::1  prefixlen 128  scopeid 0x10<host>                                                     
        loop  txqueuelen 1  (Local Loopback)        
        RX packets 0  bytes 0 (0.0 B)               
        RX errors 0  dropped 0  overruns 0  frame 0 
        TX packets 0  bytes 0 (0.0 B)               
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0                                       

tap0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500                                               
        inet 169.254.97.119  netmask 255.255.0.0  broadcast 169.254.255.255                              
        inet6 fe80::942e:1e8e:e926:c260  prefixlen 64  scopeid 0x20<link>                                
        ether 4a:6b:a6:f2:e9:e3  txqueuelen 1000  (Ethernet)                                             
        RX packets 22  bytes 6243 (6.0 KiB)         
        RX errors 0  dropped 0  overruns 0  frame 0 
        TX packets 30  bytes 4397 (4.2 KiB)         

do I have to configure something ?
Regards


#2

never mind. My fault. The reboot is a MUST.
After a reboot, the tap0 gets the right address.


#3

However, on another RaspPi same steps , now we get:

br-lan not exists!

and tap0 has the wrong address.